How-To Install Accufab’s Power Air Inlet

How-To: Install Accufab’s Power Air Inlet

Accufab’s mission is to provide the best high performance parts at competitive prices.  All items are manufactured on-site using their high-tech CNC machine shop giving them the ability for absolute control over the quality of their products.  They also staff a full-time R&D department which allows them to provide faster turn around from concept to reality.  Accufab Racing is fully committed to their customers and looks forward to continued growth as they broaden their throttle body product line while maintaining the highest quality control and customer service.

Installation of Accufab’s Power Air Inlet: For 05-07 6.0L PSD

Accufab, Inc. developed an aftermarket intake elbow called the "Power Air Inlet" for the 05-07 6.0L PSD that not only dresses up the engine and improves performance, but it is also pre-drilled and tapped to accept a 1/8" NPT male fitting which is perfect for boost gauge installation. If you’re like many Ford truck owners, you appreciate the performance of your 6.0L Power Stroke Turbo Diesel engine. Of course, it never hurts to add more power, especially if you’re towing an overloaded trailer. The Power Air Inlet was originally developed and tested by Accufab for their shop truck, an F-350 used for towing their race cars on a 48 foot trailer. The Accufab Power Air Inlet made an immediate difference during their testing. Most notably was the 1 mpg increase they experienced traveling the same roads with the same load and experiencing 2 lbs less boost to achieve the same speed. Accufab’s independent dyno tests were conducted by Jim D’Amore of JDM Engineering which showed a 9 hp advantage over stock with no other changes and an equal increase in torque.

Power Air Inlet features include:

• Airflow increased by 40%
• Lower EGT’s
• Increased mileage
• Less back pressure
• Boost port for aftermarket boost gauges
• Easy Installation
• Available in a cast or cast polished finish

As mentioned, the other notable benefit is the pre-tapped 1/8" NPT fitting on the Power Air Inlet. Like most people who tow heavy loads, or those who are strictly about performance, gauges for monitoring engine statistics are an integral part of the truck. The Power Air Inlet makes installing a 1/8 OD boost line a breeze. Gone are the days of tapping into the MAP line or pulling the stock intake elbow and drilling and tapping it yourself. A simple 3/16" hex wrench removes the 1/8 NPT plug fitting, which enables you to install any 1/8" NPT compression or Push-Lok fitting.

For Project "JAKD" we picked up some stainless steel compression fittings to match the high polished finish on the Power Air Inlet: Stainless steel compression fittings are shown below in two variations. 1. Part #: SS-200-1-2, SS Swagelok Tube Fitting, Male Connector, 1/8 in. Tube OD x 1/8 in. Male NPT (Left) 2. Part #: SS-200-2-2, SS Swagelok Tube Fitting, Male Elbow, 1/8 in. Tube OD x 1/8 in. Male NPT (Right)

 DISASSEMBLY:

Tools Required:

1. Socket Wrench
2. Universal Joint
3. 5/16" Socket
4. 7/16" Deep Socket
5. Torque Wrench

1: Identify the Stock Intake Elbow
2: The plastic shroud shown above can easily be moved out of the way to access the intake elbow bolts.  However you will need a universal joint during reassembly in order to apply the proper torque settings.
3: Loosen the band clamp on the Charge Air Cooler Pipe (CAC Pipe). There is no need to remove the clamp, just loosen it enough to allow your little finger to pass underneath. This will allow the CAC Pipe enough room to contort when you remove the elbow. Due to the length of the bolt, the band clamp shown here requires a 7/16" deep socket to remove the nut.
4: Once you have the bolts removed, get your hand underneath the intake elbow to secure the rubber O-Ring in place, and then rotate the entire assembly up towards the firewall. The rubber O-Ring is seated inside a groove under the intake elbow assembly. Although it is fairly secure, it’s a good idea to get your hand under there to prevent any chance of it dislodging and falling into the intake manifold.
5: You will note that the stock intake elbow has a bolt that comes out the side. This bolt goes through a tab that is located underneath the plastic shroud. There was no bolt that held it in place on our truck. Just make sure you rotate the elbow towards the firewall once the bolts are removed in order to dislodge the elbow from the manifold.
6: Before pulling the stock intake elbow off the CAC Pipe and installing the Accufab’s Power Air Inlet, it is a good idea to lay something down to prevent any debris from entering the manifold. With one hand securing the CAC pipe and the other securing the stock intake elbow, gently use opposing force in an up and down motion to dislodge the elbow from the CAC pipe. You will probably have to crawl up into your engine bay to get enough leverage in order to pull them apart.
7: Seen here is a comparison shot of the OEM unit and the Accufab Power Air Inlet.
8: Once you have the stock elbow off the truck, remove the rubber O-Ring and place it on the new Power Air Inlet. The rubber O-Ring is reusable. Stock elbow with O-Ring attached: Power Air Inlet showing the grove for the reusable rubber O-Ring: Power Air Inlet shown with rubber O-Ring installed:

REASSEMBLY:

9: Reassembling the Power Air Inlet is simply the reverse procedure used for removing the stock intake elbow. Position the Power Air Inlet upside down and with one hand secure the CAC pipe and with the other secure the Power Air Inlet. Use opposing force in a gentle up and down motion to secure the Inlet into the CAC pipe. Note: Ensure you push the Power Air Inlet in far enough for the grooves to get seated in the CAC pipe.
10: Once the Power Air Inlet has been seated into the CAC pipe, rotate the assembly down and seat the inlet onto the manifold. Reinsert the four bolts using a 5/16" socket, and tighten them down using a criss cross pattern to 23 ft lbs of torque. The last step in this procedure is using a 7/16" deep socket to secure the band clap around the CAC pipe. Tighten the band clamp to 12.0 nm or 8.9 ft lbs.
11: As you can see below, the Accufab Power Air Inlet does a fantastic job dressing up the engine. The enhancement from unrestricted airflow is definitely an added benefit. The 1/8" NPT tap makes it simple to install a boost line. We will determine which compression fitting we will use (straight or elbow) when we install our Autometer Ultra-Lite II gauges. The determining factor to the compression fitting used will be boost tube clearance from the engine mounted fuel filter cap when servicing the fuel filters.

Due to the success of the 05-07 Power Air Inlets, Accufab, Inc will be developing elbows for the 2003-2004 6.0L PSD. The difference between the model years is the 03-04 models uses an EGR Throttle Plate to assist the flow of exhaust gasses through the EGR Valve. As a result, the Power Air Inlet will be shorter in height as shown below.

SOURCES: Accufab, Inc. www.accufabracing.com Tweet Comments: Category: How-To If you enjoyed this article, subscribe to receive more just like it. Subscribe via RSS Feed Privacy guaranteed. We'll never share your info. Our Sponsors   Advertise with us Subscribe Enter your email address below to receive updates each time we publish new content.. Privacy guaranteed. We'll never share your info. Recent Posts Is this the replacement to the Humvee? Ford recalls 2011-2012 F-150, Expedition and Lincoln Navigator Carroll Shelby passes away at 89 Land Rover celebrates the one millionth Discovery as only Land Rover can… by driving 8,000 miles around the world GM prepares to temporarily shut down full size truck plants as refresh for the Silverado and Sierra begin New Truck Buying Resources Research the latest on the new Ford F150, and view pricing guides for the Toyota Tacoma and Chevrolet Silverado with detailed spec information and value ratings. See what stacks up against the latest truck and SUV models, including the Jeep Wrangler. Muscle Car Blog Pass the Grey Poupon… Bentley is heading back to Le Mans No room in the garage? Why not stick an Ariel Atom in your living room? Carroll Shelby passes away at 89 Jag F-Type will sport a V8 Let the Free Trade Agreement begin! Corvette now available in South Korea Motorz Season 5 Episode 6 now online! Bugatti creates one-off Wei Long edition Veyron so it can, you know… stand out The 2013 Mustang Shelby GT500 does not have 650 horsepower… it has 662 Hot Links Motorz TV Truck Hownd FordF150.net Truck Jam Truck Accessories Truck Parts Ford F-150 Videos OBD-II Codes Full Size Chevy Vehicle Tracking Software Car Transport Our Crew Editorial Directors Chris Duke Mike Wilkes Editors Mark Ponter Rick Gideon Send us tips! © 2004-2012 X7 Media. All rights reserved. | Advertising | Contact Us Truckblog® is a registered trademark of X7 Media at the U.S. Patent and Trademark Office. Permission is required to reproduce any of our content.